After the use of explosion-proof tools in our daily work, there should be a proper maintenance phase, which is crucial to the life of the tool, because if the maintenance of explosion-proof tools is not appropriate, our tools cannot be used for a long time. We serve. First of all, we need to keep the tool in a dry place. This is to make sure that some parts of the work do not get damaged.
After 20 consecutive taps in our daily work, the surface attachments of the tool should be treated, and then used after being cleaned. Do not use it continuously so as to prevent the tool from being heated due to prolonged friction. May damage our tool products.
2, after use, clean the surface of dirt and deposits, place a dry and safe place to save.
3, tapping tool products, can not be a continuous blow, more than 10 times should have an appropriate interval, at the same time to promptly remove the debris sticky parts of the product and then continue to use.
4. Wrench products must not be overpowered, and they must not be used to stretch the fasteners by using sleeves or other metal rods and hammers (except tapping wrenches).
5, cutting edge tools should be placed in the sink and gently grind the grinding wheel, not too much force and contact with the grinding wheel for too long.
6. In the actual operation of hammering tools, it is necessary to remove the oxides on the surface of the debris and the working surface to prevent third parties from hitting.
Based on the above performance and use, it is shown that aluminum-copper alloys are more suitable for normal pressure equipment and environments where explosion-proof conditions are not strict (such as gas stations, small oil depots, etc.) during normal use. The applicability of the performance of beryllium copper alloy explosion-proof tools (such as oil refineries, gas conversion stations, gas recovery plants, drilling teams, etc.).
7, before using the product to remove the surface oil, use the steel tool reference manual.
We supply full range of abrasive tools, such as Flap Disc adhesive, Flap Disc Backing Pad, Abrasive Flap Disc , Flap Wheels , flap wheel with shaft, Abrasive Sanding Disc, Abrasive Machine , etc...
both one component epoxy adhesive and two component epoxy adhesive.
Specifications for single component epoxy adhesive for flap disc:
Appearance: Colloidal
Color: Blue / White
Odour: Slight odour
Proportion(water=1):1.42
Viscosity (25℃, mpa.s): 15000~20000
Storage time: 5℃ 6 months
Recommended curing condition: 110~130℃×4~3 hours or 150~160℃×1 hour
Hardness(Shore D): ≥90
Recommended temperture on the machine: 40-52 degree
Shearing strength(23℃, steel/steel, MPa): ≥22
Flap Wheel Glue Instructions
According to the ambient temperature, preheat adhesive among 41 ~ 46℃ before pumping into the pumping system.
Note:
1.When climate is colder, adjust preheating temperature 3 ~ 5℃ higher than normal.
2.Before use large quantities,a small quantity should be used for test.
3.This flap disc glue is a chemical product, can cause weak corrosive to skin, please note that the use of the appropriate protection, such as inadvertent contact with the skin with plenty of water rinse or alcohol wash.
4.Baking temperature is particularly important for product quality. The data provided by us is tested under accurate oven temperature control. We are strongly advised customer should adjust oven temperature according to the customer's on site condition.
Storage and transportation
Flap Disc Adhesive resin glue should keep in cool, ventilated warehouse, temperature does not exceed 40℃, relative humidity of not more than 85% ,this product is not special goods, according to the general cargo transport.
Flap Disc Adhesive Glue,Flap Wheel Glue,2 Component Epoxy Glue,Flap Wheel Adhesive,Epoxy Resin Flap Wheel Glue
Zhengzhou Jiading Abrasive Manufacturing Co.,Ltd , https://www.jd-abrasives.com