| Home>Bearing knowledge> Early damage and avoidance of engine sliding bearings (2) |
Early damage and avoidance of engine sliding bearings (2)
Source: China Bearing Network Time: 2017-11-02
| /*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089'; |
(6) bearing the outer circle bearing outer circle is the bearing has a relative transformation in the seat hole. After the bearing goes outside the circle; not only affects the heat dissipation of the bearing; simply makes the alloy inside and outside the bearing ablate; and also causes the bearing back surface damage; When the bearing is burned. The main reason is that the bearing is too short, the crown is damaged, the processing may not meet the standard.
2. Avoiding the early damage of sliding bearings is much more common than bearing incineration; therefore, it is important to avoid early damage of sliding bearings. The correct protection of sliding bearings is an effective way to reduce the early damage of bearings; it is also a reliable guarantee for the life of extended bearings. Thus; In the normal protection and repair; it is necessary to pay attention to the appearance of the bearing's alloy appearance, reverse surface, end and marginal edge; if there is an abnormal display of half-wearing signs; it is necessary to carefully identify the reasons; and adopt the corresponding method; improve Bearing operating conditions; focus on the early damage to the sliding bearings.
(1) Improve the depiction of the bearing and the process of drawing or selecting the bearing; consider the heat balance of the bearing to control the temperature rise. Because the bearing works in conflict situations; because the internal friction (viscosity) of the lubricating oil constitutes power consumption; After the heat is generated, the temperature rise of the bearing is caused; the viscosity of the lubricating oil is lowered, and the gap is changed; the babbitt alloy of the bearing is softened; when it is severe, the "burning the shaft and holding the shaft" is caused. Therefore, in the structural depiction; the upper bearing of the bearing (from the bearing) The non-loading area) is opened into the oil hole; the lubricating oil is introduced from the non-load bearing area, and the oil groove is opened in the longitudinal direction or the lateral direction with the oil inlet hole in the inner and outer surfaces of the bearing bush; the lubricating oil is evenly distributed on the journal to control the temperature rise. According to the operation of the bearing; the bearing information needs to have the following functions: conflict coefficient. Bad both the blade and the smashing stool. The ridiculous 20. The mellow oyster mushroom Hanxia 芰 浚 浚 浚 愎 愎 慷 慷Benzene is coated. Therefore, the bearing material can be selected from babbitt. Babbitt alloy can work well under stable load; but cavitation is easy to occur under unsteady load; so it is not suitable for high power engine. Lead-based alloy And low-tin-lead-based alloys have higher strength and hardness; stronger fatigue resistance and cavitation resistance; better application in high-power engines. In recent years, foreign countries have exhibited sputtering methods using physical vapor deposition. Copper-lead bearing external nickel plated with 20% tin alloy coated with pure tin may be plated with pure tin; the effect is very good. In addition; the full round oil groove bearing bush is changed to semi-circular oil groove or some oil groove bearing bush; this can not only improve the lubrication of the engine sliding bearing Situation; and can also improve its carrying ability.
(2) The repair of the improved bearing and the quality of the equipment improve the quality of the hinge of the bearing; ensure that the reverse lubrication of the bearing is not mottled; the positioning bump is intact, and the amount of spring opening is 0. 5-1. 5mm; this ensures the rear bearing of the equipment With its own elastic force and the bearing housing hole tightly fit, each end of the upper and lower bearing pads installed in the bearing housing should be 30-501μm higher than the bearing seat plane; the high output can ensure the bearing cap bolts are tightened according to the regular torque. The bearing seat is closely cooperated; the self-locking force of the conflict is satisfied; the bearing is not loose; the heat dissipation effect is good; the bearing ablation and wear are avoided; the working surface of the bearing cannot be measured by the scraping method to reach 75%-85% touch impression; When the joint is not scraped, the cooperation gap between the bearing and the journal can reach the demand. In addition, the equipment should pay attention to the processing quality of the crankshaft journal and the bearing; strictly implement the repairing process standard; avoid the improper equipment due to improper loading method and The bearing bolts have uneven torque or do not conform to the rules; then the occurrence of tortuous deformation and stress gathering; inducing early bearing damage.
(3) Reasonable selection and filling of lubricating oil In the process of application, lubricating oil with small oil film surface tension should be selected; the impact of oil flow will be reduced when the bubble formed is reduced.è ¡ ã–鹊 ã–鹊 ã–鹊 ã–鹊 æ«è±¢ åº é»¾ åº é»¾ åº é»¾ åº é»¾ åº é»¾ åº é»¾ ç° ç° ç° ç° . . . . . . . . . . . . . . . . . . . . Huan Le Valley Weisong ç•šé”– 耄 耄 耄 北 北 北 北 北 北 北 北 芊庑Ч 芊庑Ч 芊庑Ч æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡ æ³¨é‡. Different quality, different viscosity grades and different types of lubricants are used to stop mixing; the deposition time before lubricating oil filling is usually not less than 48h.
(4) When properly protecting and protecting the bearing of the engine equipment; the surface of the shaft and the bearing should be coated with the regular brand of sanitary oil. After the engine bearing is installed, the fuel switch should be closed before the initial start; I idling a few times; when the engine oil pressure gauge appears, turn it on again, turn the fuel switch on; turn the throttle to the low speed position; start the engine to investigate the operation. The idle speed can not exceed 5 minutes. Do the new machine and the overhaul engine In the running-in period, the grinding industry cooperates; during the running-in period, the load is suddenly increased and the load is sharply increased and the operation is high. The engine is completed after full-load operation for a long time; it cannot be stopped immediately; it is necessary to let the engine work at no load for medium and low speed for 15 minutes. Stop; otherwise the internal heat will not be able to escape.
Strengthen the sanitation and protection of the oil filter and crankcase ventilation equipment; replace the filter element in time according to the requirements of the manual to ensure the normal operation of the engine cooling system; control the normal temperature of the engine; avoid the "opening" of the radiator; prohibit the cooling water The car, the correct choice of fuel; precise adjustment of the gas phase and incineration timing; to avoid abnormal engine burning, timely crankshaft and bearing skills to view and adjust the operation.
Recommend to friends comments close window
| Bearing related knowledge |
| Factors affecting bearing life and the characteristics of handling rare earth ceramic bearings for static pressure imported bearings SKF double row cylindrical roller bearing type suffix to explain the main problem of sliding bearings |
This article links to http://
Please indicate the bearing network http://
Previous:The correct way to protect the universal joint cross-roller needle bearing of the car. The next part: Oscillation and temperature discrimination of NTN thrust ball bearing
PC Wire
PC wire is used in major construction projects as a means of increasing the strength of cast concrete components, ranging from railway track sleepers, ground stabilizing piles, floor beams and pipe systems. The process involves the continuous heating and stretching of a cold drawn high-carbon steel wire to produce a finished product with a much improved yield stress and greatly reduced load relaxation.
Pc Wire,Pc Wire With Indentation Wire,Pc Wire With Spiral Wire,Pc Wire With Smooth Wire
HENGSHUI YUZHENG IMPORT AND EXPORT CO., LTD. , https://www.yzironnails.com