First, the technical standard (GB/T14312-93) Introduction Waterproof clothing products made of rubber coated fabrics should meet the following requirements:
1. The physical and chemical properties of waterproof clothing fabric should meet the requirements.
2. Structure requirements for waterproof clothing 1 Protective clothing should be reasonably designed according to the requirements of different workplaces;
2 Structural styles should ensure that the wearer is free to move freely during operation and it is not easy to cause hooks, pulls, twists, and grinding to facilitate detachment.
Waterproof clothing appearance requirements:
1. The surface is smooth and clean;
2. No damage, no dead folds, bubbles, knife marks, delamination, sulfur spray, sticky. Lack of glue and other defects;
3. The sewing line is straight, the needle code is even, neat, elastic and appropriate. After the thread is broken, the needle is reconstituted with 1.5cm or more, and the suture starts from the needle with 1cm;
4. Symmetry mutual difference is not more than 0.5cm, even the difference between the length of boots and pants is less than 0.6cm;
5. The position of the trademark is correct, the writing is clear and complete without burrs;
6. The seam width is not less than 1cm, the glue width is not less than 2cm;
7. The color difference of the patch is not lower than 3.
Second, waterproof clothing product requirements
1. Protective clothing for rubber-coated fabrics Protective clothing for raincoats and waterproof garments is a protective garment made of rubber-coated fabrics, which has been cut, sewn, and glued, and is suitable for use by personnel engaged in water-spraying operations.
In addition to the product quality should be consistent with the "General Technical Conditions for waterproof clothing" (GB/T14312-93) in the relevant provisions, it should also comply with the "labor protection raincoat" (LD30-92) requirements.
The structure has a split type and a long type, and the material includes a single-sided rubber-coated fabric (type I), a double-sided rubber-coated fabric (type II), and a laminated rubber-coated fabric (type III).
Models include industrial and mineral hooded clothing, live hats, water-protective clothing, and underground protective clothing.
The main varieties and properties are as follows:
Waterproof clothing: It is made of single adhesive waterproof and single adhesive tape. It can be worn in live or hooded styles, with rubber facing outwards, inwards or on both sides. It is characterized by its lighter weight compared to double-glued and laminated waterproof garments, and its low water absorption capacity (small plastic outwards and relatively small outwards), good waterproof performance, low price, and wide application, generally open air and downhole, culverts, and showerheads. Splashing water can be applied to the workplace.
Lacquer and waterproof clothing: Made of waterproof plastic folder with adhesive tape, there are two styles: live cap and hood. Specifications and size of a single waterproof clothing features the same, better wear resistance and aging resistance. The inner surface is a cloth layer, and after the sweat evaporates, it is partially absorbed by the cloth, so it is more comfortable to wear. However, due to the thin coating layer, water leakage is likely to occur after aging, and then the weight increases and it is not easy to dry. Suitable for laborers in open-air operations such as forestry, transportation, and field exploration.
Raincoat: Raincoats are available in single, double and triple sizes. Live and hooded styles, short shawls (handling), single ponchos, single-glue, male and female. Double-breasted, farmer-style, Tibetan, laminated rubber herdsman style and cycling style.
2. Under the water, water pants, aquatic products under the water, water pants: the water is made from a half-boots and caps attached by a jumper, and a waistband. There are two types of caps, clothing, pants, boots and gloves that are joined together and live caps are not. Its bonding method, raw sticky and sticky two. Underwater trousers consist of a pair of semi-boots, a pair of straps, and a waistband. Divided into single and two kinds of plastic. Water resistant pants and watering garments have strong water resistance and sewage resistance and are suitable for shallow water aquaculture, drainage, sewerage, culverts, drainage pipes and downhole drainage. According to the depth of wading, the water depth limit of the watering garment does not exceed the shallow water level of the heart, and diving is strictly prohibited; the water depth of the water trousers does not exceed the crotch.
Aquatic products: Aquatic products include aquatic tops (hats), apron trousers (with straps), aquatic aprons, sleeves, and other types. Aquatic clothing is 50% plastic, with natural 1,2 rubber, and 0.75mm thick. . After the pieces are cut into pieces, they are made of raw and sticky clothes and are vulcanized. It is resistant to seawater, sunlight, and anti-sun fins. It can prevent fins and sharp bones and is suitable for live fisheries, aquaculture and food processing operations.
First, the technical standard (GB/T14312-93) Introduction Waterproof clothing products made of rubber coated fabrics should meet the following requirements:
1. The physical and chemical properties of waterproof clothing fabric should meet the requirements.
2. Structure requirements for waterproof clothing 1 Protective clothing should be reasonably designed according to the requirements of different workplaces;
2 Structural styles should ensure that the wearer is free to move freely during operation and it is not easy to cause hooks, pulls, twists, and grinding to facilitate detachment.
Waterproof clothing appearance requirements:
1. The surface is smooth and clean;
2. No damage, no dead folds, bubbles, knife marks, delamination, sulfur spray, sticky. Lack of glue and other defects;
3. The sewing line is straight, the needle code is even, neat, elastic and appropriate. After the thread is broken, the needle is reconstituted with 1.5cm or more, and the suture starts from the needle with 1cm;
4. Symmetry mutual difference is not more than 0.5cm, even the difference between the length of boots and pants is less than 0.6cm;
5. The position of the trademark is correct, the writing is clear and complete without burrs;
6. The seam width is not less than 1cm, the glue width is not less than 2cm;
7. The color difference of the patch is not lower than 3.
Second, waterproof clothing product requirements
1. Protective clothing for rubber-coated fabrics Protective clothing for raincoats and waterproof garments is a protective garment made of rubber-coated fabrics, which has been cut, sewn, and glued, and is suitable for use by personnel engaged in water-spraying operations.
In addition to the product quality should be consistent with the "General Technical Conditions for waterproof clothing" (GB/T14312-93) in the relevant provisions, it should also comply with the "labor protection raincoat" (LD30-92) requirements.
The structure has a split type and a long type, and the material includes a single-sided rubber-coated fabric (type I), a double-sided rubber-coated fabric (type II), and a laminated rubber-coated fabric (type III).
Models include industrial and mineral hooded clothing, live hats, water-protective clothing, and underground protective clothing.
The main varieties and properties are as follows:
Waterproof clothing: It is made of single adhesive waterproof and single adhesive tape. It can be worn in live or hooded styles, with rubber facing outwards, inwards or on both sides. It is characterized by its lighter weight compared to double-glued and laminated waterproof garments, and its low water absorption capacity (small plastic outwards and relatively small outwards), good waterproof performance, low price, and wide application, generally open air and downhole, culverts, and showerheads. Splashing water can be applied to the workplace.
Lacquer and waterproof clothing: Made of waterproof plastic folder with adhesive tape, there are two styles: live cap and hood. Specifications and size of a single waterproof clothing features the same, better wear resistance and aging resistance. The inner surface is a cloth layer, and after the sweat evaporates, it is partially absorbed by the cloth, so it is more comfortable to wear. However, due to the thin coating layer, water leakage is likely to occur after aging, and then the weight increases and it is not easy to dry. Suitable for laborers in open-air operations such as forestry, transportation, and field exploration.
Raincoat: Raincoats are available in single, double and triple sizes. Live and hooded styles, short shawls (handling), single ponchos, single-glue, male and female. Double-breasted, farmer-style, Tibetan, laminated rubber herdsman style and cycling style.
2. Under the water, water pants, aquatic products under the water, water pants: the water is made from a half-boots and caps attached by a jumper, and a waistband. There are two types of caps, clothing, pants, boots and gloves that are joined together and live caps are not. Its bonding method, raw sticky and sticky two. Underwater trousers consist of a pair of semi-boots, a pair of straps, and a waistband. Divided into single and two kinds of plastic. Water resistant pants and watering garments have strong water resistance and sewage resistance and are suitable for shallow water aquaculture, drainage, sewerage, culverts, drainage pipes and downhole drainage. According to the depth of wading, the water depth limit of the watering garment does not exceed the shallow water level of the heart, and diving is strictly prohibited; the water depth of the water trousers does not exceed the crotch.
Aquatic products: Aquatic products include aquatic tops (hats), apron trousers (with straps), aquatic aprons, sleeves, and other types. Aquatic clothing is 50% plastic, with natural 1,2 rubber, and 0.75mm thick. . After the pieces are cut into pieces, they are made of raw and sticky clothes and are vulcanized. It is resistant to seawater, sunlight, and anti-sun fins. It can prevent fins and sharp bones and is suitable for live fisheries, aquaculture and food processing operations.
China Labor Insurance Network
LED Mouse Lights,Outdoor Mouse Lights,Outdoor Cartoon Rat Lights,Cartoon Rat Lights Lights
Sichuan Kangruntengpu Photoelectric Technology Co., Ltd. , https://www.tengpulighting.com