Indoor tile press location can be divided into: wall tiles and floor tiles. Experts say that wall tiles should strictly belong to ceramic products and floor tiles are usually porcelain products. Their physical properties are different. Both of them differ greatly in the selection of clay ingredients and firing techniques. The water absorption rate of wall tiles is about 10%. It is several times higher than a floor tile with a water absorption of only 1%.
The floor of the bathroom and kitchen should be laid with low water absorption floor tiles, because the ground will often use a lot of water to wash, so that tiles can not be affected by water vapor, do not absorb stains. Wall tiles are made of glazed ceramics and have a high moisture content. Its back surface is generally rough, which also helps adhesives put wall tiles on walls. Tiles are not easily affixed on the walls. Wall tiles used on the ground will absorb too much water and become difficult to clean. It can be seen that walls and floor tiles cannot be mixed.
Before laying the wall, the ground should be leveled before the tiling should clean up the ground, such as lime plaster, latex paint, wallpaper, etc. on the wall. Decorations, or dirt on the ground, be sure to clean, otherwise cement The mortar is not firmly bonded to the base; in addition, if the wall itself has cracks, it should be properly treated before it can be tiled, so as to avoid future cracks in the basic structure caused by cracking or falling off; in addition, for the flatness or vertical For floors and walls where the gap is too large, cement mortar should be used for leveling treatment.
The laying of the order of stress floor tiles should be attached from the inside to the outside, such as the slope of the ground or a floor leakage, should pay attention to the direction of the slope to find the drainage; wall tiles should be laid from the bottom, for the sake of beauty, the bottom of the brick should be posted . After pressing the tiles, press the floor tiles. When there are half bricks, you should try to place them below. In addition, a wall cannot be attached to the top at a time to prevent the tile from being heavy and causing it to fall.
Wall tiles should be fully immersed in water because wall tiles have a high moisture content, which must be taken into account when pasting. Before the tiling, the base layer should be fully moistened with water, and the tiles should be fully dried in the water for at least 20 minutes. Otherwise, the moisture in the mortar is rapidly absorbed by the dried substrate and tile and condenses quickly, which affects the adhesion fastness. Otherwise, the tiles will absorb moisture from the cement so that the cement cannot function as an adhesive. In addition, the water absorption rate of each type of wall tile is not the same, which depends on the experience of the construction team to grasp.
Paving tiles do not underestimate the details of the yin and yang corners to reflect the most quality, therefore, people's home decoration
Pay special attention to the treatment of edges and corners. Tiles are indispensable materials for home decoration. People find that the junction between two walls is the most difficult to handle. In the past, the practice was to grind the tiles at a 45-degree angle and then dock them, or to tile one of the walls directly to the other wall, so that the cross-section of the tiles was exposed and not beautiful. The reporter found a PVC yin and yang corner in Dongfang Home Building Materials Supermarket. It was designed for this purpose.According to the sales staff of Beijing Donghang Decoration Co., Ltd., which distributes this product, before the appearance of the product, the corners of the tiles were more difficult to handle. People used porcelain yin and yang angles, but because it is easy to fall off, the colors are monotonous and the specifications are single. , was soon eliminated by the market, and later used 45-degree edging method, but this process has a large workload, edging will produce a lot of dust, edging process increases the tile breakage rate, sharp edge that is easy to break It is also easy to hurt people and other shortcomings. The invention of the PVC Yin Yang angle completely solves the problem of the processing of the corners of the tiles. It is a revolutionary product of the tile paving process. The product has obtained the utility model patent and design patent of the State Patent Office. People in the industry called this product a "tile partner" because it made it much easier to tile the tiles and save time and money. According to reports, there are more than 40 kinds of colors in this tile corner line, with the color tiles on the market. Material selection is PVC material and imported stabilizers, which can be curved to match the curved wall corner, divided into Yin and Yang angles, matt, light, and hot film three varieties.
At present, some building materials markets have sales of similar products, but many are made of poor quality PVC, which is much cheaper. It is understood that the performance of poor-quality tile corners is unstable and easy to fade. Because of the poor quality calcium carbonate added to the formula, brittle deformation is easy to occur. Although the corner line is inconspicuous, but once the deformation, fracture, it will affect the overall effect of the tile, remove the ceramic tile replacement is quite troublesome, so remind consumers to buy the corner line to bend it to try its toughness, view its color, to see if shiny.
The back of the cabinet is also covered with tiles. Many families now buy sets of cabinets. Do not think that the space behind the cabinet can't be seen anyway, so that the walls are bare, but it should be covered with ceramic tiles behind the cabinets. First, the tiles are the best protection for the kitchen wall waterproofing layer; secondly, the tiles will greatly reduce the kitchen moisture to the cabinets and prevent the cabinets from being moldy and deformed. Some tiles, such as median Spanish tiles, Omega tiles, RAK tiles, etc., add moisture proof and acid proof functions according to the kitchen features, and are more suitable for the complex environment of the kitchen. Third, due to the different specifications of the tiles, the countertops of the cabinets may not coincide with the seams of the tiles. . If there is a tile on the back of the cabinet, you don't have to slicing the tiles and affecting the appearance.
Vitrified tiles are only harder than ceramic tiles, so they are usually laid out in the kitchen.
In addition, we must pay attention to buying a vitrified tile to buy better, or to easily penetrate into the oil. Now a new process of vitrified tiles, using nanotechnology, add a micro powder, it is said to be very spiritual. In addition, to buy a vitrified tile should pay attention to the point is to pay attention to the material of vitrified tiles, marble does not Well, there is some radiation.
Tiles Tiles Tiles Floor tiles Cement Decorating design Lacquer-lacquer flooring Tiles Marble tiles Cabinets for home cabinets Kitchen cabinets Wall tiles Kitchen cabinets Doors Tiles for bathroom Tiles for bathroom Colors for toilets Wall tiles Bathrooms waterproof Price overall bathroom Bathrooms design Toilets for bathroom Tiles for tiles Ceramic tile Price kitchen Tile tile specifications
High speed shutter door is a rapid operating, anti-crash shutter door for indoor application . The most advantage of this door is that the opening/closing speed can reach to 0.6-1.8m/s, really fast action a lot than tranditional rollling shutter door. short opening and closing times reduce cooling loss, avoid airflow and enable a smooth operating procedure. They can also be designed in larger dimensions for the mining and aircraft industries.
High speed door can be easily installed, economical,quiet and efficient with electromechanical drive.
This door quickly though in/out open gate, ideal for warehouses,factories, hangars use, widths can be from 2m to 20 meters.
The material of this door are variety: PVC curtain to keep the insdie clean, heavy duty aluminum door with wind-resisitant function can wrok in heavy windy weather, and also the freezer door can be used in cold warehouse or somewhere like that.
Including models are:PVC High Speed Door, Aluminum Spiral High Speed Door, Self-Recovery repair door, Cold Storage Room Fast Door.
High Speed Door,PVC High Speed Door,Aluminum High Speed Door,Spiral High Speed Door
Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.hfautodoors.com