Pipeline dredge According to different sources of power, dredge machines can be roughly divided into two types: manual type dredge machines and electric type dredge machines. Everyone may have encountered problems with sewers or toilets, and they will usually find a professional company to solve them. In fact, they can completely solve themselves. Pipe blockage protracted and painstaking, manual processing pipeline blockage is very troublesome, please clear the company did not want to waste money, so here pipeline dredge machine is a good choice, the price is not too expensive, not only effortless but also very simple, that drain How to use the machine ? Need to pay attention to what you use, let's look at it with Xiaobian.
Main purpose of pipeline dredging machine
1. Indoor and outdoor sewage main pipeline: It can thoroughly solve the backwater situation of the bottom sewer caused by various reasons, eliminating the trouble of high cost for your planing. The effect after cleaning can reach more than 95%. This equipment is also used for outdoor pipes.
2. Toilet: professional dredge all kinds of models (cloth, plastic) caused by a variety of soft and hard materials, professional disassembly.
3. The pit: because the pit has become a long time, the pipe elbow produced a thick layer of urine alkali, from 100MM slowly into 50M or even 10MM and even blocked, resulting in slow water into the pit, easy Blocking,
4. Floor drain, vegetable pond: Professional dredge floor drain of various v-shaped and s-shaped turn, (because the decoration is dropped into the cement, sand or hair and other debris caused by clogging.)
5. Basins, basins: professional dredge all kinds of basins, including (V-type, S-type) and other channels.
6. Bathtub, shower room: professional tools to clear all kinds of debris caused by the plug, professional disassembly and installation.
How to use the pipe dredging machine
First, the use of electric pipe dredging machine is to pass the special dredge spring through the pipe dredging machine, and then extend to the location of the pipe plug, open the power supply, depress the brace of the tightening spring, and gradually throw the spring forward in the pipeline through the dredge spring. Move the blocked pipe. If the steel spring becomes entangled with the blockage, it can be pulled back a bit and continue to clear at normal speed. When a blockage is encountered, the steel spring is pulled forward again for a certain distance so that it forms an arc with the nozzle, and then this section of steel spring is pressed firmly so that the torque is transmitted to the opening head to open the plug. If the blockage is cleared, the steel spring must be dredged a few feet more forward to confirm that the blockage in the pipe has been completely opened. During the entire process of retrieving the steel spring from the pipeline, the water must be continuously flushed to flush the obstruction, and the steel spring can also be flushed.
Second, there are two ports on the electric dredge machine. The opening on the newly unpacked machine is the entrance to the dredge spring. Opposite the face with the automatic head is to clear the spring exit. There is always one hand holding the steel spring for control throughout the sparse journey.
When you are operating a dredge machine to clear, the "feel" of the steel spring forward in the pipeline is very important: Do not pull too many steel springs from the machine all at once; too many steel springs are easily twisted outside the pipe mouth , causing knots. Remember to always turn the machine forward, whether it is sending steel springs or retracting steel springs.
The reversal function can be used only when the steel spring is obstructed by the blockage and the reversing function can be used, or when the P-shaped curve is passed, the reversal can be properly used to facilitate the passage of the steel spring through the curve. When the steel spring hits a plug, let the steel spring maintain its own "rhythm" to clear it. When the steel spring is clearing the blockage, it is necessary to pay attention to the reaction of the steel spring. If it is found that the blockage is difficult to pass through, the steel spring must be properly withdrawn, and the steel spring must be slowly opened forward. After the steel springs have finished clearing the blockage, the steel ropes must be dredged forward several feet to ensure that the pipeline has been cleared.
Third, the 100-type and 80-type internal structure is exactly the same. Both are equipped with, and use two kinds of different clearance springs of 16mm and 10mm thickness. Since the two springs are used as the only access channel for the dredging machine, they cannot be used at the same time.
4. When using a 10mm thin spring in the drum, the automatic head cannot be used, and the spring's entry and exit can be pulled out or pushed freely from the drum bin hung on the machine by hand. But remember not to pull the entire spring completely out of the drum! Therefore, in fact, the slender spring is only suitable for dredging the sink of the wash basin with a distance of about 2 meters.
5. When using the 16mm thick spring in the iron basket, it is necessary to remove the drum hung on the machine. Pass the spring from the entrance of the original hanging drum, pass through the outlet with the automatic head, and install the upper cutter head to clear the blocked position of the sewer pipe.
As the machine is started, the entire connection of the dredge spring will flick up, so be careful not to half of the dredge spring mounted on the machine in the machine, half in the iron basket! According to the normal procedure, the unplugging spring shall be connected outside the inlet of the dredge according to the length required for clearing the concrete. Taking into account the home dredge generally only equipped with a 12-meter dredge spring. So you just have to pull the whole spring out of the iron basket when you start the machine.
Pipeline dredge safety precautions
1. The pipe dredging machine must use single-pole three-pole plugs and sockets with good protection grounding.
2. It is easy to cause water accumulation in the work site after the pipeline is blocked. When using the pipeline dredging machine in the stagnant and wet environment, appropriate safety precautions should be adopted. For example, the leakage protection device is used to place the main unit in the absence of stagnant water. Dry position. The operator wears insulated gloves, wears insulated shoes or stands on an insulating mat.
3, when using and cleaning dredge machine, should prevent the host from entering the water. Inadvertent water infeeds must not be used until they are not dry.
4. The pipeline dredging machine should use the fuse with rated voltage and standard capacity, and can not use alternatives such as wire.
5. Do not pull the power cord when moving the machine or unplugging the plug.
6. When working in a narrow place or special environment (such as boiler room, pipeline, wet zone, etc.), there should be guardianship.
7. Non-professionals shall not disassemble and repair the pipeline dredging machine without permission.
8. After the operation is completed, the power supply should be cut off first, and then the on-site cleaning and maintenance of the pipe dredging machine should be performed.
9. When using and cleaning the machine, the inside of the host should be prevented from entering the water. Inadvertent water infeeds must not be used until they are not dry.
10. After the operation is completed, the power supply should be cut off first, and then the on-site cleaning and maintenance work of the Guangzhou pipeline dredging machine should be done.
11. It is forbidden to use the trouble dredge machine to operate.
Summary: The above is related information on the use of pipe dredging machines and precautions. It is for reference only and hopefully helps everyone. If you want to know more related information, you can pay attention to this website information.
Building Materials Knowledge Spring Decoration Knowledge Summer Decoration Knowledge Autumn Decoration Knowledge Family Decoration Notes
Support provides a clothes hanging rod support device, which is mainly used for hanging clothes in the wardrobe, which comprises a seat body. The seat body is provided with a support part supporting the end of the clothes hanging rod. The connection makes it easy to take out the clothes hanging rod after hanging, and the clothes hanging rod will not slide and cause the falling of parts. It is convenient and fast in installation and maintenance.
Hanging Rail Tube Support,Hanging Tube Support,Steel Tube Support,Metal Tube Support
GuangDong XinCheng Material CO.,LTD , https://www.xin-alu.com